Abrasive Blades


Abrasive cutting is the most common method of sectioning to achieve a clean and efficient cut. Buehler's abrasive blades are designed to provide high quality sectioning results with no burning and minimal surface deformation.

Buehler carries a wide range of different metallographic abrasive blades for sectioning machines that can be used for many different applications. Our abrasive blades have diameter ranges from 5 in (127 mm) to 18 in (455 mm), arbor sizes ranging from 0.5 in (12.7 mm) to 1.25 in (31.75 mm), blade thicknesses ranging from 0.0020 in (0.5 mm) to 0.063 in (1.6 mm) and dimensions ranging from 5.9 in (150 mm) to 9 in (230 mm).

Our abrasive blades are frequently used for sectioning many different materials including but not limited to ferrous materials, soft, medium, hard, and tool steel, stainless steel, super alloys, titanium alloys, and zirconium alloys.

Efficient Cutting with Extended Life: 

  • To acheive a clean and efficient cut, a blade needs to break down during cutting to expose new abrasive particles. Depending on the hardness of the material, the blade needs to break down at different rates. Buehler's abrasive blades have been developed for specific applications to ensure the proper rate of wear. This balance provides an efficient cutting action while maximizing blade life. The selection table on the "Ordering" tab provides the recommendations by material type and hardness.

Thin, Precise Abrasive Sectioning:

  • For certain applications, it is important to minimize the amount of damage done to the sample during sectioning. The AcuThin series offers thin blades that have been developed to minimize the area of cutting thus reducing the amount of damage to the sample. These blades allow for precise, delicate abrasive sectioning with minimal surface damage.
 

Wide Diameter Range: 

  • With abrasive blades from 5"  [127mm] up to 18" [455mm], Buehler's abrasive blades can be used on Buehler's full range of abrasive and precision saws.

No specifications to show at the moment.

Abrasive Blades Selection, 1.25in [32mm] Arbor (Qty 10)
[Blade Thickness is listed under Part Number] Rubber Bond = • Resin Bond = *
Recommended Use 9in [230mm]
Chop/Linear
10in [254mm]
Chop/Linear
12in [305mm]
Chop/Linear
12in [305mm]
Orbital
14in [356mm]
Chop/Linear
14in [356mm]
Orbital
Super Alloys and General Steel, Non-ferrous 12-4205-010•
0.055in [1.4mm]
12-4405-010•
0.055in [1.4mm]
12-4405-010•
0.055in [1.4mm]
12-4305-010•
0.063in [1.6mm]
12-4305-010•
0.063in [1.6mm]
Ferrous materials >HRC60 10-4110-010•
0.07in [1.8mm]

102309P*
0.06in [1.5mm]
10-4210-010•
0.07in [1.8mm]

102509P*
0.06in [1.5mm]
12-4110-010•
0.105in [2.7mm]

103009P*
0.079in [2mm]
12-4410-010•
0.105in [2.7mm]
10-4310-010•
0.075in [1.9mm]

103509P*
0.098in [2.5mm]
12-4310-010•
0.105in [2.7mm]
Ferrous materials HRC50-60 10-4112-010•
0.07in [1.8mm]

102310P*
0.06in [1.5mm]
10-4212-010•
0.07in [1.8mm]
10-4412-010•
0.105in [2.7mm]
12-4410-010•
0.105in [2.7mm]
10-4312-010•
0.115in [2.9mm]

103509P*
0.098in [2.5mm]
12-4310-010•
0.105in [2.7mm]
Ferrous materials HRC35-50 10-4116-010•
0.07in [1.8mm]
10-4216-010•
0.07in [1.8mm]

102510P*
0.06in [1.5mm]
12-4116-010•
0.105in [2.7mm]

103010P*
0.079in [2mm]
12-4416-010•
0.105in [2.7mm]
12-4305-010•
0.063in [1.6mm]

103510P*
0.098in [2.5mm]
12-4316-010•
0.105in [2.7mm]
Ferrous materials HRC15-35 10-4120-010•
0.07in [1.8mm]
10-4220-010•
0.063in [1.6mm]

102511P*
0.06in [1.5mm]
12-4120-010•
0.105in [2.7mm]

103011P*
0.079in [2mm]
12-4420-010•
0.105in [2.7mm]
12-4305-010•
0.063in [1.6mm]

103511P*
0.098in [2.5mm]
12-4320-010•
0.105in [2.7mm]
High Speed Steel, Stainless Steel, Carburized Steel
102308P*
0.06in [1.5mm]

102508P*
0.06in [1.6mm]

103008P*
0.079in [2mm]

103508P*
0.098in [2.5mm]
Delicate Cutting 10-4127-010•
0.063in [1.6mm]
10-4227-010•
0.032in [0.8mm]
Titanium Alloys, Zirconium Alloys, Ductile Metals 10-4145-010•
0.063in [1.6mm]

102307P*
0.06in [1.5mm]
10-4245-010•
0.063in [1.6mm]

102507P*
0.06in [1.5mm]
12-4145-010•
0.055in [1.4mm]

103007P*
0.079in [2mm]
10-4345-010•
0.075in [1.9mm]

103507P*
0.098in [2.5mm]
Non-Ferrous Materials (Aluminum, Copper, Brass) Very Soft Ferrous Materials 10-4150-010•
0.063in [1.6mm]
10-4250-010•
0.063in [1.6mm]

102512P*
0.06in [1.5mm]

103012P*
0.079in [2mm]
10-4350-010•
0.105in [2.7mm]

103512P*
0.098in [2.5mm]
General Use 102301
0.032in [0.8mm]
102501
0.04in [1mm]

10-4360-010&nbs
0.032in [[0.8mm]
10-3501
0.063in [1.6mm]
Ferrous Materials >HRC45 10-4161-010
0.025in [0.635mm]
10-4261-010
0.025in [0.635mm]
10-4361-010
0.025in [0.635mm]
103502
0.105in [2.7mm]
Recommended Use 16in [406mm]
Orbital
18in [455mm]
Orbital
Super Alloys and General Steel, Non-ferrous 12-5605-010•
0.075in [1.9mm]
12-5805-010•
0.1in [2.5mm]
Ferrous materials >HRC60 12-5610-010•
0.125in [3mm]
12-5810-010•
0.153in [3.8mm]
Ferrous materials HRC50-60 12-5612-010•
0.125in [3mm]
12-5816-010•
0.153in [3.8mm]
Ferrous materials HRC35-50 12-5616-010•
0.125in [3mm]
12-5816-010•
0.153in [3.8mm]
Ferrous materials HRC15-35 12-5616-010•
0.125in [3mm]
12-5816-010•
0.153in [3.8mm]
High Speed Steel, Stainless Steel, Carburized Steel
Delicate Cutting
Titanium Alloys, Zirconium Alloys, Ductile Metals 12-5645-010•
0.075in [1.9mm]
12-5845-010•
0.1in [2.5mm]
Non-Ferrous Materials (Aluminum, Copper, Brass) Very Soft Ferrous Materials
General Use
Ferrous Materials >HRC45
AcuThin™ Abrasive Blades for IsoMet™ Precision Cutters, 0.5in [12.7mm] Arbor (Qty 10)
[Blade Thickness is listed under Part Number]
Use with Saws IsoMet High Speed IsoMet High Speed IsoMet High Speed IsoMet High Speed Pro Only
Recommended Use 5in [127mm] 7in [178mm] 150mm 200mm
Tool Steel, hard steel, HRC45 & Up 10-4060-010
0.019in [0.48mm]
Medium hard, soft steel, HRC45 & Below 10-4061-010
0.019in [0.48mm]
Steel, Stainless Steel 11-4207-010
0.030in [0.76mm]
Hard, soft non-ferrous material 11-4217-010
0.030in [0.76mm]
Soft Materials 101520
0.50mm
102020
0.50mm
Tough Materials and General Use 1015998E
1mm
1020998E
1.5mm


Abrasive Blades
Sorry no videos at the moment.